 | | | |
|
|
|
| | |
|
- INTRODUCTION
-
The GPS-003 consists of a high-performance GPS engine board based on the industrial leading
architecture, a low profile patch antenna, and a conventional RS-232 transceiver. It provides fast
positioning and instant real time navigation capability, even in a urban canyon, while consuming
little power.
- The GPS-003 delivers quality navigation information to a PC through its standard serial port at
4800/9600 baud rate in GPS enabled map software. The GPS-003 will help you arrive at your destination comfortably
and effortlessly.
- The GPS-003 is a single unit capable of interfacing with a wide variety of application software and Navigation equipment.
Plug-Navigate-Position is the new GPS-003 Receiver/Antenna
concept. When integrated with your Personal Computer
running a Map Software, the GPS-003 provides real-time position of your vehicle and helps you navigate to your next
destination. The GPS-003 Mobile locator is a low cost/high quality GPS solution for integrating
to an AVL, Fleet Management System and Marine Navigational Aid. The unit is a single GPS
Receiver/Antenna in a low profile waterproof sealed enclosure with a magnetic base
mount. It interfaces to a serial port (RS 232) of your computing device.
- GENERAL FEATURES
- Ultra small (size of an active antenna)
- Integrated Antenna
- 12 Channel Parallel
- Instant reacquisition
- RS-232 Interface
- Low power consumption
- Water resistant enclosure
- Magnet base
- Light weight
- APPLICATIONS
- Car navigation and tracking
- Automobile Tracking
- PDA, Loptop, Car PC...
- Vehicle monitoring and dispatching
- Outdoor activities positioning
- Marine and Boaters guidance
- SPECIFICATIONS
- Performance
- Antenna: Integrated built-in patch antenna
- Frequency: L1 1575.42MHz , C/A code
- Sensitivity: -135dBm (typical)
- Channels: 12 channels with HW Track@ simultaneously \\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\"all-in-view\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\" tracking
- Operation modes: 2D/3D automatic selection
- Acquisition time:
- cold start : 48 sec
- warm start : 38 sec
- hot start : 8 sec
- Reacquisition: < 0.1 sec
- Position update: 1 Hz
- Velocity 0.05m /sec
- Time +/- 1 us
- Accuracy Position: 15m CEP without S/A
- Electrical
- Primary power: 3.5~5.5 volts DC,
PS/2 male connector *
- Current: 120mA
- Interface
- Protocol: NMEA-0183 V2.20, RS-232, 8-N-1 *
- Data Baud rate: 4800bps or 9600bps
- NMEA message: GGA, GLL, GSA, GSV, RMC and VTG *
- Connector: standard RS232 DB9 female connector
- Physical
- Dimension: 57mm×44mm×22mm, (2.2\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\"×1.7\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\"×0.8\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\")
- Weight: 48gram without cable
- Environmental
- Temperature: operation: -30º to 75ºC, -40º to 85ºC Industrial
- storage: -55º to 100ºC
- Operation Humidity 5% to 95%
- Dynamics: altitude: -1000 ~ +18,000m
- velocity : 500m / sec
- acceleration : < 4g
- HOW TO USE THE GPS-003
- Step 1. Plug RS-232 to COM port to your Notebook PC or Handheld PC.
- Step 2. Plug PS/2 connector in the PS/2 mouse outlet of your Notebook PC.
- Step 3. Place your GPS-003 on the outside roof of your Vehicle with magnetic base, or put the GPS-003 on the place without metal shielded.
- Step 4. Power on your Notebook PC or Handheld PC.
- Step 5. Choose the correct COM port for running a map or navigation software.
- Notice :
- 1. Make sure the power is off before started.
- 2. For safety, do not proceed the above steps while driving.
- 3. Recommended to apply the clipper for individual locating, navigation, geographical survey as
outdoors.
- 4. For the best satellite signal reception, GPS-003 must keep horizontal while using the clipper.
- 5. In order to see NMEA0183 navigation data, set the Hyper Terminal program of port connected
with GPS-003 to
- Baud rate : 4800 or 9600
- Data bit : 8
- Party : None
- Stop bit : 1
- Flow control : None
|
|
